Technical question: Older Sturmey Archer gear hubs e.g. AW series are cheap and plentiful. Anyone here familiar with their workings?
I want to find out the feasibility of converting one to left hand drive. Could it be as simple as reversing the two sets of pawls in their respective ratchets?
This is a static archive of our old forum. Most features inc files and downloads work but some links are now dead
Please refer to Our Website or our Facebook Groupfor latest info.
Please refer to Our Website or our Facebook Groupfor latest info.
Sturmey Archer Hubs
- dralphs
- Site Admin

- Posts: 553
- Joined: Fri Nov 14, 2014 11:50 pm
- Location: Oxford
- Team: Falcon Notnray
- Contact:
Re: Sturmey Archer Hubs
I think probably not as the ratchet teeth will be the wrong way round
but take a look at http://sheldonbrown.com/sturmey-archer/aw.html
or
https://chestercycling.wordpress.com/20 ... er-aw-hub/
there is also lots of diagrams and documents on the SA heritage site, eg for yours look at
http://www.sturmey-archerheritage.com/i ... ail&id=837
but take a look at http://sheldonbrown.com/sturmey-archer/aw.html
or
https://chestercycling.wordpress.com/20 ... er-aw-hub/
there is also lots of diagrams and documents on the SA heritage site, eg for yours look at
http://www.sturmey-archerheritage.com/i ... ail&id=837
Re: Sturmey Archer Hubs
Thanks for the links dralphs. I see what you mean now about the teeth.
The right hand ratchet looks like it might be reversible by parting off the threaded part of the R.H. ball cup and welding it back on flipped over, assuming it's made of steel.
The left hand (low gear) one might be more tricky as it's integral to the shell on the newer hubs, according to the 1973 service manual. On older drawings the L.H. ball cup and ratchet appears to be threaded into the shell, but from what I can see from various photos, the later ones have no means of unscrewing it if that was still the case.
I wonder if the tooth ring might just be pressed into the shell. If not, maybe new teeth could be broached in-situ somehow. Or maybe I could just remove those pawls all together and blank off the lowest gear.
The right hand ratchet looks like it might be reversible by parting off the threaded part of the R.H. ball cup and welding it back on flipped over, assuming it's made of steel.
The left hand (low gear) one might be more tricky as it's integral to the shell on the newer hubs, according to the 1973 service manual. On older drawings the L.H. ball cup and ratchet appears to be threaded into the shell, but from what I can see from various photos, the later ones have no means of unscrewing it if that was still the case.
I wonder if the tooth ring might just be pressed into the shell. If not, maybe new teeth could be broached in-situ somehow. Or maybe I could just remove those pawls all together and blank off the lowest gear.
Re: Sturmey Archer Hubs
I procured myself a rusty 1985 vintage AW hub yesterday evening to pull apart. Lots of rust, water and gammy grease inside meant it was past its best so I don't feel too bad about sacrificing one in the name of science.
Happily the small low-gear pawls are bisymmetrical and will simply go back in the other way round. The larger ones that the clutch mechanism interact with are handed, but I think a kiss with the grind wheel will put a sufficient chamfer in them to make them operate the opposite way. The holes for the pawl pivots (4mm on my particular model, a real mixed bag of measurements and thread sizes) need to be redrilled to make the pivot heels line up with the square holes behind them though and this is as far as I got last night.

The ring gear is made of really hard stuff. A freshly sharpened cobalt HSS bit barely scratches the surface. I guess this is probably key to their reliability. I'm going to borrow a solid carbide bit to try on it next.
The teeth inside the ratchets may well be just as hard. I was thinking of making a broach from an HSS blank and progressively scrape the little wedge shapes out, but I might have to make something that takes a carbide insert instead.

Happily the small low-gear pawls are bisymmetrical and will simply go back in the other way round. The larger ones that the clutch mechanism interact with are handed, but I think a kiss with the grind wheel will put a sufficient chamfer in them to make them operate the opposite way. The holes for the pawl pivots (4mm on my particular model, a real mixed bag of measurements and thread sizes) need to be redrilled to make the pivot heels line up with the square holes behind them though and this is as far as I got last night.

The ring gear is made of really hard stuff. A freshly sharpened cobalt HSS bit barely scratches the surface. I guess this is probably key to their reliability. I'm going to borrow a solid carbide bit to try on it next.
The teeth inside the ratchets may well be just as hard. I was thinking of making a broach from an HSS blank and progressively scrape the little wedge shapes out, but I might have to make something that takes a carbide insert instead.

- dralphs
- Site Admin

- Posts: 553
- Joined: Fri Nov 14, 2014 11:50 pm
- Location: Oxford
- Team: Falcon Notnray
- Contact:
Re: Sturmey Archer Hubs
Glad you are making progress
I suspect the ratchet may be case hardened, worth googling to see if anyone knows
I suspect the ratchet may be case hardened, worth googling to see if anyone knows
