This is a static archive of our old forum. Most features inc files and downloads work but some links are now dead
Please refer to Our Website or our Facebook Groupfor latest info.

timing tag position

BFPCR committee members only
All committee business in here. Please move topics found in other areas if needed to here for committee to discuss
User avatar
Wing Racers
Team Manager
Team Manager
Posts: 59
Joined: Tue Nov 18, 2014 8:14 pm
Team: Wing Racers

timing tag position

Post by Wing Racers »

Hi All, we tried a new timing tag position at Solihull which I thought we be an improvement, by judging by the amount of dropped laps was a dismal failure. :(
The old position was the tag hung of the chassis cross member 6" off the floor next to the steel steering arms and chain, with the label facing forward and the tag vertical...the new position placed on the correx floor, label forward, vertical, 3" off the floor with no metal within 6".
If I hadn't been otherwise entertained i would have changed it back to the old position after the first race.
Any ideas?
Wing Racers
______________________
2015 PC1 Champions
User avatar
dralphs
Site Admin
Site Admin
Posts: 553
Joined: Fri Nov 14, 2014 11:50 pm
Location: Oxford
Team: Falcon Notnray
Contact:

Re: timing tag position

Post by dralphs »

Ours are cabled tied to our front crossmember that supports the steering hub/axle
Its has the grey side forwards and hangs vertically
WP_20150721_002.jpg
I did wonder if yours is an old tag and failing but according to the zip data file its newer (higher number) than all ours.
Thats not to say that it isn't EOL and failing.
I don't know if Phil keeps the data but the timing kit can show failing battery or other tag issues so might be worth asking Phil to check it at Blackbushe or just get it swopped for a new one.
Dave
Falcon Notnray Racing
www.yarntonscouts.org.uk
User avatar
dralphs
Site Admin
Site Admin
Posts: 553
Joined: Fri Nov 14, 2014 11:50 pm
Location: Oxford
Team: Falcon Notnray
Contact:

Re: timing tag position

Post by dralphs »

looking at the data from Wombwell, i'd go back to that position or change the tag
Dave
Falcon Notnray Racing
www.yarntonscouts.org.uk
gcre
Licenced Driver
Licenced Driver
Posts: 98
Joined: Sat Nov 15, 2014 11:33 pm

Re: timing tag position

Post by gcre »

I moved ours from zip-tied just under a steel cross member -probably 150mm above ground, to no where near any corex and 50mm above ground for Shenington. Its possibly made a marginal improvement. But we run ours black face forwards.... !?!
Jes@GCRE
Pedalcar racer
Pedalcar racer
Posts: 522
Joined: Sat Nov 15, 2014 11:34 pm

Re: timing tag position

Post by Jes@GCRE »

This popped up again on Saturday.

Generally there were some issues so poor Mark and Phil had a less pleasent day than they deserved.

Firstly, I should apologise for the attitude of "Hair" in the Swebbelli pit who responded to Mark's request by rudely assuming that the problem couldn't possibly be ours. Bad attitude and I had words with him again on Sunday about it.

Secondly, it does seem that all the front runners were missing laps although tags were as Graham has described above (the one on car #8 wasn't - but it was exactly as I inherited the car from MRowley at the start of the year though unless it had slipped).

Was it that we were losing half the loop or was it something we had done wrong in setting up?

No blame on anyone but I think it's worth addressing while fresh in the mind.

Thanks to the efforts of race control in keeping on top of this so well through such a long event.

Jes
User avatar
dralphs
Site Admin
Site Admin
Posts: 553
Joined: Fri Nov 14, 2014 11:50 pm
Location: Oxford
Team: Falcon Notnray
Contact:

Re: timing tag position

Post by dralphs »

When i get the mat and control box later in week (it went home in trailer with kevin as i had to go to cardiff) i will check it over and see if anything is off. However the two loops span the full width and are sequential one after the other.

see the census manual at http://identec.com/manuals/appendices.pdf

Mark and i did discuss it and wonder if we can tweak the loops to improve it or somehow space them apart more, but that would mean two mats since getting wider rubber matting is impossible unless you pay exorbitant prices. there is also the problem of transportation and storage.

Comparing results with say Blackbushe (wing 4 dropped in 286) the mat was far worse at Curborough (wing 11 dropped in 378)

The only difference i can see is that the mat had the gantry tripods on it and also had power cables adjacent to it for the lights. Shenington also had high dropped laps and also had gantry/lights.

Given how the system works, i suspect for the fastest cars it may be getting near to its limit and any additional interference from mains hum won't help. after rechecking the manual it does state to keep the loops away from metal so think that's the first and easiest option.

There is also a mention that PC monitors can radiate interference at 100kHz which is very close to the tag frequency. None of us have considered this and whilst the timing screen in the trailer wasn't that close it may have been close enough, since it states in the manual make sure PC monitors are 1.5M x reading range away and suggests 4.5M for a 2M square loop.
Note at blackbushe the monitor was further away and we had fewer drops - conicidence or is that the problem.

Digging deeper. For speeds up to 30mph the loop width should be 2.5M, it also states that no single side of teh loop should exceed 4M.
We have 1M wide x 7M long although identec did think we would be ok. We may need to reconfigure back to the old layout but that brings its own problems.

Unfortunately the drops weren't consistant enough for us to say its one particular issue. We may need a bit of tech help from identec, maybe even a trip to their factory with the kit and a car to let them see how ot works.
Dave
Falcon Notnray Racing
www.yarntonscouts.org.uk
User avatar
dralphs
Site Admin
Site Admin
Posts: 553
Joined: Fri Nov 14, 2014 11:50 pm
Location: Oxford
Team: Falcon Notnray
Contact:

Re: timing tag position

Post by dralphs »

Mark

Can you enquire about prices for TD2 http://identec.com/products/census/service-aid/td2.html and
MS3 http://identec.com/datasheets/MS3.pdf

TD2 would be useful when setting up (assuming it works on our census unit).

Whilst MS3 useful, once we have used it to check the tuning it probably won't get used again. Can you ask if we can rent or borrow one for a week or two
Dave
Falcon Notnray Racing
www.yarntonscouts.org.uk
User avatar
AlanGoodman
Site Admin
Site Admin
Posts: 424
Joined: Thu Nov 06, 2014 9:13 am
Location: Hemel Hempstead
Team: Apollo Racing
Contact:

Re: timing tag position

Post by AlanGoodman »

The gantry/cabling does sound to be the likely suspect to me... This may be way off the mark, but I'll throw it in anyway - The cars at the top end of the field tend to be the ones with the better, more complex lighting systems, rather than just little cycle lights on the corners... At Shenington and Curborough the lights would have been in place but not at Blackbushe? Any chance of interference there?
User avatar
dralphs
Site Admin
Site Admin
Posts: 553
Joined: Fri Nov 14, 2014 11:50 pm
Location: Oxford
Team: Falcon Notnray
Contact:

Re: timing tag position

Post by dralphs »

Alan

Its possible. they all use similar high power led headlights that drive the led using a high frequency converter.
Ours whilst similar are mounted in a steel tube welded to the chassis which is also earthed to battery negative so they are essentially sheilded so might explain why we aren't affected.

Will be interesting to check the zip file and see if the drops increase as it gets dark
Dave
Falcon Notnray Racing
www.yarntonscouts.org.uk
gcre
Licenced Driver
Licenced Driver
Posts: 98
Joined: Sat Nov 15, 2014 11:33 pm

Re: timing tag position

Post by gcre »

Shenington drops were mainly due to the longer outage with the dongle I think. I'd more suspect the high-speed loop position and reduced loop width maybe but that's just a suspicion.
gcre
Licenced Driver
Licenced Driver
Posts: 98
Joined: Sat Nov 15, 2014 11:33 pm

Re: timing tag position

Post by gcre »

Can I just add that the top three cars dropped 50 laps between them on Saturday and Phil, Mark, Bob etc did a SUPERB job in catching the vast vast majority so that the race result was never in question and rightly so. :)

I'm now thinking how I can use my 'work' skills to provide more real-time help on this... ;)
Jes@GCRE
Pedalcar racer
Pedalcar racer
Posts: 522
Joined: Sat Nov 15, 2014 11:34 pm

Re: timing tag position

Post by Jes@GCRE »

The 3 Swebbelli cars also use LED lights - not sure about the others but these are very much part of the sport now and here to stay I am afraid.

For reference I switched on car 4's lights when I was on my in-lap with about 2 hrs 20 minutes to go because the switch is in a tricky place and I didn't think anyone else would be able to find it. Car 1 had it's lights turned on about an hour later I think.

Fitting steel tubes for lights isn't really an option unless if became mandatory :) .
Jes@GCRE
Pedalcar racer
Pedalcar racer
Posts: 522
Joined: Sat Nov 15, 2014 11:34 pm

Re: timing tag position

Post by Jes@GCRE »

By the way, this forum sees "F-I-T-T-I-N-G" as a dirty word! XD
User avatar
dralphs
Site Admin
Site Admin
Posts: 553
Joined: Fri Nov 14, 2014 11:50 pm
Location: Oxford
Team: Falcon Notnray
Contact:

Re: timing tag position

Post by dralphs »

Jes@GCRE wrote:By the way, this forum sees "F-I-T-T-I-N-G" as a dirty word! XD
well im sure someone somewhere gets their kicks out of seing photos of n-a-k-e-d pedalcars and how good the f-i-t-t-i-n-g of their bodywork is :lol:
Dave
Falcon Notnray Racing
www.yarntonscouts.org.uk
User avatar
AlanGoodman
Site Admin
Site Admin
Posts: 424
Joined: Thu Nov 06, 2014 9:13 am
Location: Hemel Hempstead
Team: Apollo Racing
Contact:

Re: timing tag position

Post by AlanGoodman »

Phwoarrrrr! :o